Kondenzátor vodní K573H, 4Pass, Bitzer

Design safety
Certified according to the European Pressure Equipment Directive 2014/68/EU

Design features

• Heat exchanger pipes: made from Cu or Cu-Ni (saltwater resistant version) with newly developed pipe geometry and a “low fouling” profile on the cooling medium side
• Heat exchanger pipes are soldered into breaker plates to ensure a secure seal
• mantle pipes and breaker plates made from pressure vessel steel P 265 GH
• Recirculating cap:
  - removable, allows pipes to be mechanically cleaned
  - connection and deflecting side interchangeable
  - cooling medium outlet from K573H(B)
  - additional bleeding plugs from K38 03T(B)
• Breaker plates with plastic coating
• Cooling medium connections: Threaded pipe or flange
• inspection glass as standard
• Mounting brackets
  - bottom: vessel labelled as “N”
  - top and bottom: vessel labelled as “H” (for installing single compressors) and “T” (for single and tandem compressors)
• Refrigerant connections
  - pressurised gas: Rotalock adapter/solder connector with flange K1053H(B) and above
  - refrigerant outlet: shut-off valve
  - alternative refrigerant outlet from model K123HB
• Rotalock connections for pressure relief valve
  - inner thread 3/a'' -18 NPTF
  - outer thread 1 ¼” - 12 UNF
• suitable for (H)CFC / HFC refrigerants (refrigerants with a temperature glide > 2 K on request)
• Maximum permitted pressure/temperature
  - refrigerant side: 28 bar / -10 °C to 120 °C
  - cooling medium side: 10 bar / -10 °C (with antifreeze agent) to 95 °C
• inert gas filling

bundled pipe condensers with refrigerant outlet at the bottom can also be used as pressurised gas desuperheaters.

Special versions:

• Salt water resistant version:
  - Cu-Ni pipe, recirculating cap with plastic coating
• recirculating cap with plastic coating for standard version with Cu pipes
• mounting rails or plates (e.g. for installing compressor)
• adapter for connecting the pressure relief valve on all models
• threaded or welding neck flange
• refrigerant inlet and outlet with various adapter and valve combinations
• conforms to foreign regulations and various certification societies (e.g. Bureau Veritas, Germanischer Lloyd, Lloyd's Register of Shipping)

Scope of delivery / accessories
4-pass design corresponds to standard version

Performance data
The specified compressor performance is based on valves measured at a pressurised gas temperature of 90 °C and a cooling medium cleanliness factor r= 0.4 x 1 o-4 m2 K/W.


Condenser design
Calculating of condenser capacity Q

When selecting a condenser it is first necessary to determine the condenser capacity Q. Condensing capacity can be calculated in two different ways:

Condensing capacity as the sum of the refrigeration capacity and power consumption
This method adds together the refrigeration capacity and power consumption of the compressor (or compressors in a power rack). Performance data can be found in the compressor information leaflets or in the software.

Estimation using factors
A simplified method can also be employed for typical designs. To determine condensing capacity, the refrigeration capacity of the compressor is multiplied by the factor in the following diagram.
 

ParametrHodnotaHmotnostHmotnost netto61,0 kgObecné informaceTypBündelrohrverflüssigerChladicí náboj32, 4 kg / chladivo = R 134AChladicí náboj28, 3 kg / chladivo = R 404AChladicí náboj32, 0 kg / chladivo = R 22TypK573HTyp kondenzacewassergekühltfür Verdichter4VES-6Y.. 4NES-20YObjemChladicí strana29,4 dm ³Střední strana chlazení5,8 dm ³Připojení2 přihrávkaG 2 Inch4 přihrávkaG 11 / 4 Inch2 přihrávkaG 2 Inch4 přihrávkaG 11 / 4 InchRotalockové připojeníVýstup1, 3 μg 4 "-12 InchInlet1, 3 μg 4 "-12 InchRozměryPrůměr216 mmSpojení potrubíPrůměr28 L / mmPrůměr11 / 8 " / palcePrůměrL 35 L / mmPrůměr13 / 8 " / palceÚdaje o výkonnostiDte 10K83200 WDte 15K124800 WDte 10K66800 WDte 15K100200 W2 přihrávka0,30 bar4 přihrávka0,59 bar2 přihrávka5. 09 / l / s2 přihrávka18, 32 / m ³ / h4 přihrávka2. 31 / l / s4 přihrávka8, 33 / m ³ / h